Bronkhorst

μ-FLOW L01

(초)저유량 열식 액체 질량 유량계

  • 빠르고 정확한 측정 신호
  • 설치 포지션에 덜 민감함
  • 매우 작은 내부 볼륨 (센서: 1,5...33 μl)
  • 끓는점이 낮은 액체에 적합
  • Analog, RS232 혹은 필드버스 통신
Get a quote 다운로드 Datasheet
μ-FLOWL01

Liquid Mass Flow Meters for Ultra Low Flow Rates

Bronkhorst® model L01 Liquid Flow Meters (LFMs) are suited for precise measurement of flow ranges between 5…100 mg/h and 0,1...2 g/h at operating pressures up to 400 bar. The LFM consists of a thermal mass flow sensor and a microprocessor based pc-board with signal and fieldbus conversion and a PID controller for optional mass flow control by means of a separately mounted control valve.

μ-FLOW series are equipped with a digital pc-board, offering high accuracy, excellent temperature stability and fast response. The main digital pc-board contains all of the general functions needed for measurement and control. In addition to the standard RS232 output the instruments also offer analog I/O. As an option, an on-board interface can be mounted to provide CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS protocols.


기술 정보

Measurement / control system
Flow range (intermediate ranges available)min. 5…100 mg/h
max. 0,1…2 g/h
(based on H2O)
정확도 (선형도) (실제 검교정 기반)± 2 % FS
Repeatability< 0,2 % FS (typical H2O)
Turndown ratio1:20 (5…100%)
Operating temperature5 … 50 °C
Temperature sensitivity± 0,2% FS/°C
Attitude sensitivitynegligible
Warm-up timeapprox. 10 min. for accuracy ± 2% FS
Mechanical parts
Material (wetted parts)stainless steel 316L/320;
other on request
Pressure rating (PN)400 bar abs
Process connections1/16” or 1/8” OD compression type; other on request
(<1 g/h we advise to use 1/16" only)
SealsMetal
Ingress protectionIP40
Electrical properties
Power supply+15 … 24 Vdc +/-10%
Max. power consumption
Supply
15 V
24 V
at voltage I/O
100 mA
65 mA
at current I/O
120 mA
85 mA
extra for fieldbus
<75 mA
<50 mA
아날로그 출력0…5 (10) Vdc or 0 (4)…20 mA (sourcing output)
Digital communicationstandard: RS232;
options: CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS
Electrical connection
아날로그/RS2329-pin D-connector (male)
PROFIBUS DPbus: 9-pin D-connector (female);
power: 9-pin D-connector (male)
CANopen® / DeviceNet™5-pin M12-connector (male)
FLOW-BUS/Modbus-RTU/ASCIIRJ45 modular jack
Modbus TCP / EtherNet/IP / POWERLINK2 x RJ45 modular jack (in/out);
Control valve options
External actuator options to be connected to the controller
Certification for hazardous areas
Approvals / certificates

Technical specifications subject to change without notice.

도면 및 배선연결 정보 제품 페이지 우리의 웹사이트

Downloads

Brochures
LIQUI-FLOW - µ-FLOW brochure
Manuals
Manual LIQUI-FLOW incl u-FLOW
Hook-up diagrams
Analog IO - RS232
DeviceNet
EtherCAT
FLOW-BUS
Modbus RTU/ASCII
PROFIBUS DP
PROFINET
CANopen
EtherNet/IP
Modbus-TCP
POWERLINK
Optional Bus and IO Configurations
Dimensional drawing
Dimensional drawing μ-FLOW L01


BRONKHORST KOREA Co. Ltd

경기도 화성시 동탄순환대로 830 SK
V1 Center 209호
대표자 : 헨드리크제지너스타펠
사업자등록번호 : 119-86-74469

           Social Responsibility
Copyright © 2024 Bronkhorst. All rights reserved.     Sitemap     Disclaimer     Privacy note