Bronkhorst

mini CORI-FLOW™ M13V10I

Lage flow Coriolis massflowregelaar voor gassen

  • Hoge nauwkeurigheid, uitstekende herhaalbaarheid
  • Snelle reactietijd
  • Onafhankelijk van vloeistofeigenschappen
  • Additionele dichtheid en temperatuur output
  • Compact, robuust (IP65) ontwerp
  • Optionele ATEX-goedkeuring Cat.3, zone 2
  • Klepfunctie: Normally closed
Vraag offerte aan Downloads Ondersteuning
mini CORI-FLOW™M13V10I

Low Flow Coriolis Mass Flow Controllers for Gases

mini CORI-FLOW™ Mass Flow Meters and Controllers are precise and compact instruments, based on the Coriolis measuring principle, designed to cover the needs of the low flow market. Bronkhorst® model M13V10I Mass Flow Controller (MFC) is suited for highly accurate control of gas flow ranges between 1…50 g/h and 40…2000 g/h (which corresponds with 13,3…666 mln/min up to 0,53…26,6 ln/min when used on nitrogen) at operating pressures up to 100 bar (higher on request). The instruments are equipped with a robust IP65 weatherproof housing and are optionally available with ATEX approval for use in Zone 2 hazardous areas.

The instrument contains a microprocessor based pc-board with signal and fieldbus conversion and a PID controller for mass flow control by means of an integrated control valve (normally closed).


Technische specificaties

Meet- / regelsysteem
Flowbereik (tussenliggende bereiken beschikbaar)min. 1…50 g/h;
max. 40…2000 g/h
Nauwkeurigheid massflowmeting± 0,5 % of rate
Herhaalbaarheid±0,05% of rate ± ½(ZS* x 100/actual flow)%
Turndown ratio1:50
Nulpunt stabiliteit (ZS)≤ ± 0,2 g/h
(Guaranteed at constant temperature and for unchanging process and environment conditions.)
Settling time (in regeling, typisch)1 sec. (typical)
Temperatuureffecton zero: < 0,02 g/h/°C;
on span: < 0,001% Rd/°C;
self heating (at zero flow): < 15°C
(Depends on flow rate, heat capacity fluid, T amb., T fluid and cooling capacity.)
Bedrijfstemperatuur0 … 70 °C ;
for ATEX Cat.3, Zone 2 max. 50°C
MontageAny position, attitude sensitivity negligible.
Instrument to be rigidly bolted to a stiff and heavy mass or construction for guaranteed zero stability.
External shocks or vibrations should be avoided.
Nauwkeurigheid temperatuurmeting± 0,5 °C
Nauwkeurigheid dichtheidsmeting≤ ± 5 kg/m³
Max. Kv-waarde2,4 x 10-3
Lekdichtheid, naar buiten< 2 x 10-9 mbar l/s He
Opwarmtijd> 30 min. for optimum accuracy
Mechanische delen
Sensorsingle tube, DN 0,5
KlepzittingKalrez®-6375, other on request
Materiaal (onderdelen die in contact komen met het medium)stainless steel 316L or comparable
Behuizingstainless steel 430F
Drukclassificatie100 bar abs
Procesaansluitingenknelkoppelingen of face seal (VCR/VCO) koppelingen (gelast)
Afdichtingenmetal
Gewicht1,5 kg
Beschermingsgraad (behuizing)IP65 (weatherproof)
Elektrische eigenschappen
Stroomvoorziening+15…24 Vdc +/- 10%;
Max. ripple recommended: 50 mV tt
Max. stroomverbruikmax. 7 W
Analoog signaal0…5 (10) Vdc, min. load impedance > 2 kΩ;
0 (4)…20 mA (sourcing), max. load impedance < 375 Ω
Analoog setpoint0…5 (10) Vdc, min. load impedance > 100 kΩ;
0 (4)…20 mA (sourcing), max. load impedance ~ 250 Ω
Digitale communicatiestandard: RS232;
options: PROFIBUS DP, DeviceNet™, Modbus RTU of FLOW-BUS
Elektrische aansluiting
Analoog/RS2328-pin DIN (male);
PROFIBUS DPbus: 5-pin M12 (female);
power: 8-pin DIN (male);
CANopen® / DeviceNet™5-pin M12 (male);
FLOW-BUS/Modbus-RTU/ASCII5-pin M12 (male);
Control valve options
Externe actuatoropties die op de controller moeten worden aangesloten
Ex-proof specificaties
Goedkeuringen / certificaten

Technische specificaties kunnen zonder kennisgeving worden gewijzigd.

Voor technische maattekeningen en aansluitschema's bezoekt u de productpagina op onze website

Downloads

Brochures
MINI CORI-FLOW M12-M14 brochure

Manuals
MINI CORI-FLOW Manual
MINI CORI-FLOW Quick Installation Guide

Hook-up diagrams
Analog I-O RS232
DeviceNet
FLOW-BUS
Modbus
PROFIBUS DP

Dimensional drawing
Meters - compression type weld adapters
Meters - VCR type machined adapters
Controllers - compression type weld adapters
Controllers - VCR type machined adapters
C5I Controllers - compression type weld adapters
C2I Controllers - compression type weld adapters
Controllers - on a 2 kg mass block
Controllers - on a 4 kg mass block

Solids 3D
M12V10I-M13V10I-M14V10I 1-4VCR
M12V10I-M13V10I-M14V10I excl. adapters
Mass block mini Cori-Flow Mxx 2kg
Mass block mini Cori-Flow Mxx 4kg


Bronkhorst NEDERLAND

Lunet 10c
3905 NW Veenendaal
Tel. +31 (0)318 55 12 80
[email protected]

Copyright © 2020 Bronkhorst. All rights reserved.     Sitemap     Disclaimer     Privacy note