Bronkhorst

μ-FLOW L01V12

超低流量熱質式液體質量流量控制器

  • 快速準確的測量信號
  • 對安裝位置不敏感
  • 非常小的內部體積
  • 適用於低沸點液體
  • 模擬、RS232 或現場總線通信
詢價 下載 數據表
μ-FLOWL01V12

Liquid Mass Flow Controllers for low flow rates

Bronkhorst® model L01V12 Liquid Flow Controllers (LFCs) are suited for precise measurement and control of flow ranges between 5…100 mg/h and 0,1...2 g/h at operating pressures up to 100 bar. The LFC consists of a thermal mass flow sensor and a microprocessor based pc-board with signal and fieldbus conversion and a PID controller for mass flow control by means of an integrated control valve.

μ-FLOW series are equipped with a digital pc-board, offering high accuracy, excellent temperature stability and fast response. The main digital pc-board contains all of the general functions needed for measurement and control. In addition to the standard RS232 output the instruments also offer analog I/O. As an option, an on-board interface can be mounted to provide DeviceNet™, PROFIBUS DP, Modbus or FLOW-BUS protocols.


Technical specifications

Measurement / control system
Flow range (intermediate ranges available)min. 5…100 mg/h
max. 0,1…2 g/h
(based on H2O)
Accuracy (incl. linearity) (based on actual calibration)± 2 % FS
Repeatability< 0,2 % FS (typical H2O)
Turndown ratio1:20 (5…100%)
Settling time (in control, typical)2 … 4 sec.
Operating temperature5 … 50 °C
Temperature sensitivity± 0,2% FS/°C
Max. Kv-value2,37x10-3
Max. fluid viscosity0.1 Pa*s
Attitude sensitivitynegligible
Warm-up timeapprox.10 min. for accuracy ± 2% FS
Mechanical parts
Material (wetted parts)stainless steel 316L/320;
other on request
Pressure rating (PN)100 bar abs
Max. ΔP10 bar dif.
Process connections1/16” or 1/8” OD compression type; other on request
(<1 g/h we advise to use 1/16" only)
Purge connection1/16” OD compression type
SealsKalrez®-6375;
others on request
Ingress protectionIP40
Electrical properties
Power supply+15 … 24 Vdc +/-10%
Max. power consumption
Supply
15 V
24 V
at voltage I/O
285 mA
250 mA
at current I/O
305 mA
270 mA
extra for fieldbus
<75 mA
<50 mA
Analog output0…5(10) Vdc or 0 (4)…20 mA (sourcing output)
Digital communicationstandard: RS232;
options: CANopen®, DeviceNet™, EtherCAT®, PROFIBUS DP, PROFINET, Modbus RTU, ASCII or TCP/IP, EtherNet/IP, POWERLINK or FLOW-BUS
Electrical connection
Analog/RS2329-pin D-connector (male)
PROFIBUS DPbus: 9-pin D-connector (female);
power: 9-pin D-connector (male)
CANopen® / DeviceNet™5-pin M12-connector (male)
FLOW-BUS/Modbus-RTU/ASCIIRJ45 modular jack
Modbus TCP / EtherNet/IP / POWERLINK2 x RJ45 modular jack (in/out);
Control valve options
External actuator options to be connected to the controller
Certification for hazardous areas
Approvals / certificates

Technical specifications subject to change without notice.

For dimensional drawings and hook-up diagrams please visit the product page on our website

Downloads

Brochures
Manuals
General manual digital instruments
Operating instructions digital instruments
Hook-up diagrams
Analog IO - RS232
DeviceNet
FLOW-BUS
Modbus
PROFIBUS DP
Dimensional drawing
Dimensional drawing μ-FLOW L01V12


台灣柏朗豪斯特股份有限公司

新竹縣竹北市台元街三十八號四樓之一、二
Rm. 1 & 2, 4F., No.38, Taiyuan St., Zhubei City, Hsinchu County 302, Taiwan (R.O.C.)
電話 +886 3-5600-518
[email protected]

            Social Responsibility
Copyright © 2024 Bronkhorst. All rights reserved.     Sitemap     Disclaimer     Privacy note